The EVO MFG 3.5” JL Enforcer Lift Suspension Systems lift your 2018+Jeep Wrangler JL 3.5”s. Our main goal in developing this kit was togive a performance ride on and off road while giving added vehiclelift. The JL Enforcer kits are specifically designed to lift your JLand maintain a performance spring rate, smooth ride quality while havingthe option of retaining factory shocks, maintaining wheel travel withuse of shock extensions (part number EXT kits) or without shockextensions to allow for use of your choice of aftermarket 3-5” liftshocks or use of our EVO SPEC 2.5” Remote Reservoir King Shocks. Thesekits come with a set of 3.5” lift springs specific to each corner whichwill keep the Jeep Wrangler JL level side to side. EVO MFG JL Enforcerkits are available in multiple configurations to suit your needs andbudget and are upgradable down the road. 3.5” kits come with raisedrear trackbar track to center axle and correct roll center for improvedhandling. What are the JL Enforcer OVERLAND Systems, EVO-3012 Kits? The difference with EVO MFG Enforcer Overland systems (EVO-3012s) vs EVOMFG Enforcer systems (EVO-3011s) is the use of front Overland ControlArm Brackets. When lifting your vehicle your control arms at rideheight have a steeper angle towards the floor which can have somenegative effect/chop in ride quality. With the use of the includedOverland Control Arm brackets we relocate the front control arm mountinglocations at the frame. In doing this when lifted we maintain factoryflatter control arm angles and while minimal, we alleviate much of thechop associated with lifting a Jeep giving even better and more improvedride quality. Also, in the use of Overland Drop Brackets we are able toengineer more performance into the front suspension to improve brakingand driveline angles through suspension cycle. Both kits drive verywell, the Overland Kits are better suited for less hard off-roadcrawling and more light off road and on road use. The EVO MFG 3.5" JLEnforcer Kits are easy to install using normal tools. No drilling orcutting (optional rear shock extensions require one minor drill). Theyrequire no driveshaft or exhaust modifications (your shock choice mayrequire this, contact manufacturer to be sure). Simple Bolt oninstallation. 3.5” lift is based on increase of a 4 Door Rubicon. 4Door Sport and Sahara Models will see slightly higher increases overstock and will match overall lift height of a Rubicon Model. 2 DoorModels (all) will see slightly higher increases in lift. Increases willvary. Stage 1 kits includes all the necessary parts to lift your JL3.5”s. Stage 2 kits includes Stage 1 components as well as EVO MFGEnforcer JL Front Lower Adjustable Control Arms to allow for casteradjustments. Stage 3 Kits includes stage 2 components as well as EVO MFGEnforcer rear upper adjustable control arms for rear pinion angleadjustment Stage 4 kits includes stages 1 components with all 8 EVO MFGEnforcer control arms for full front and rear axle adjustments. *Allpart number “EXT” kits include front and rear shock extensions. “K” Kitsinclude EVO SPEC King Shocks. Retaining factory shocks while maintainingfull wheel travel. Note: Depending on actual tire variances and sizes,Some trimming of body sheet metal, fenders, bumpers and inner fenderliner may be required with stated tire sizes to fully clear undercompression.
All 3.5" JL Enforcer its require wheel spacers or aftermarket wheels with smaller backspacing.
Front aftermarket driveshaft is not required when equipped with EVO Spec King Shocks
Adjustable Front Trackbar is required to complete proper installation, Front and rear adjustable trackbars are included with PLUS “P” kits
INSTALLATION TIME 4-6 HOURS
